New DryLube Bearings from SKF (Lansdale, PA) eliminate the need for grease relubrication and are designed to perform virtually maintenance-free over a wide temperature range. Filled with a dry lubricant based on graphite or molybdenum disulfide and a resin binder, the dry lubricant maintains a thin film on the bearing’s rolling elements to protect against metal-to-metal contact and any potential damage caused by solid contaminants.
PristineFG food-grade lubricant for rotary compressors from Sullair (Michigan City, IN) is a long-lasting synthetic lubricant that maintains product quality and increases equipment performance. Now available for use by food processors and packagers, beverage bottlers, and pharmaceutical manufacturers, this lubricant complies with current FDA and USDA H1 regulations.
A new Bulk Bag Filling Line from Flexicon (Bethlehem, PA) automatically dispenses pallets, fills bulk bags, and accumulates filled bags for removal by forklift. The dispenser, which holds up to 15 pallets, is equipped with a powered roller conveyor that removes the bottom-most pallet from the stack, and positions it beneath the cantilevered fill head.
The new LPS monitor from CAT PUMPS (Minneapolis, MN) is designed to sense water leakage past the low pressure seals and alert maintenance personnel that the pump seals need replacing before pump drive components are at risk. Models are available for PLC or PC interfaces, and an indicator light model is are available when a PC or PLC interface is not used.
Kroil from Kano Laboratories (Nashville, TN) dissolves rust and lubricates to loosen frozen metal parts. Kroil’s unique molecular structure facilitates penetration while maintaining a structure that breaks bonds due to corrosion or compression. It is available in 8 sizes, including a new 16.
Ruhrpumpen (Tulsa, OK) has added the new centrifugal pump model CPP-L to its standard product line. The CPP-L is the low flow version of the CPP-21. The new pump complies with the ANSI B73.1 Standard and can be used to replace existing equipment without piping or base changes. The radial vane impellers for the CPP-L are designed to provide better hydraulic control and reduce the thrust load to prolong the bearing and seal’s life.
The new Type II AccuFlow Safety Can from Justrite Mfg. Co. (Mattoon, IL) was built to meet OSHA and the National Fire Protection Association requirements. Protection features include an internal stainless steel flame arrester that dissipates heat to prevent flashback ignition and a gasketed, self-closing leak proof lid that automatically vents to guard against explosion.
The TechAngle Electronic Torque Wrench from Snap-on Industrial (Kenosha, WI) is now available with a cycle-counting feature which helps track required calibration cycles of torque-measuring instruments. Designed to do the work of four torque wrenches, the wrench allows users to set the torque value in Newton meters, foot pounds, or inch pounds, and angle of rotation.
TwisterBand TB30 from igus (East Providence, RI) is a compact carrier system that makes rapid rotating movements possible up to 3,000 degrees and depends only on the belt length or design height in the axis of rotations. The smaller masses involved allow lower centrifugal forces and rotary speeds up to 720 degrees.
The Lumetronic Slider Light from National Electric (Commerce, CA) utilizes Lumetronic LEDs, the next step in rechargeable work lights with more efficient LEDs and nearly three times the brightness of ordinary LED rechargeable worklights. Its oval shape prevents rolling and fits easily in pockets.
Dialight (Farmingdale, NJ) has unveiled its new SafeSite Series LED Area Light, a compact, high-output Class I and Class II, Div 1 certified LED Area Light. Approved for use in Class I, Div 1 Groups B, C, Dl; and Class II, Div 1 Groups E, F, and G hazardous locations, the light is designed to replace up to 150-watt HID fixtures.
Hitachi America, Ltd. (Tarrytown, NY) has announced the SJ700-2200HFU2 model inverter, with a 440 A output current capability. The SJ700 can develop more than 200 percent starting torque at 0.3 Hz and 150 percent torque near 0 Hz. Another feature is the SJ700 is Hitachi’s EzSQ (Easy Sequence) built-in programming function—in many cases the need for a separate PLC can be eliminated.
The new AeroVent 1 from Newstripe, Inc. (Aurora, CO) can deflate aerosol cans to recyclable scrap metal. It can quickly puncture and drain a variety of aerosol can sizes, reducing the cost of hazardous waste disposal. A smaller version of the AeroVent 3, it is designed for users that have smaller quantities of cans in a variety of sizes.
The STAR TECK EXTREME DIRECTOR Cable Fitting from Thomas & Betts (Memphis, TN) is an adjustable, range-taking fitting, used to terminate metal-clad and Teck cable. Featuring a swashplate design, the fitting adjusts from 90 to 180 degrees and is available in half- and three-quarter inch NPT hub sizes.
NORDOT Adhesive #34P-4 from Synthetic Surfaces Inc. (Scotch Plains, NJ) is a new one component outdoor adhesive that was designed to install and repair synthetic turf and other outdoor surfaces in widely variable and hostile weather conditions. Allowing for year-round installation and repair, the adhesive can be applied to a dry or damp surface at any temperature and humidity in which a mechanic can work.
Hydrovane (Redditch, Worcestershire, UK) has announced its new Hydrovane V Series line of rotary vane compressors. Small, quiet, and affordable, Hydrovane compressors are all direct drive with no belts or gears to maintain. They operate at 1760 RPM’s for low stress, noise, and long compressor life.
The new A1000 Variable Speed Drive from Yaskawa America Inc. (Waukegan, IL) is compatible with interior and surface permanent magnet motors and provides up to 200 percent torque. The user-friendly configuration includes a multi-language LCD display, parameter storage, and application presets.
The Viega ProPress system from Viega (Wichita, KS) is now available for joining stainless steel piping in sizes from ½-inch to 4-inches using press technology to secure pipe connections in under seven seconds. The system of stainless steel pipe, valves, and fittings provides a flameless way for water-tight and gas-tight stainless steel joining.
Akro-Mils (Akron, OH) announces the expansion of its line of heavy-duty 19-Series Steel Storage Cabinets to include five drawer colors—black, blue, gray, red, and yellow. Ideal for storing, consolidating, and organizing small parts, these cabinets are available in six models and feature a heavy-duty welded steel frame.
LEVALIGN EXPERT from Ludeca Inc. (Doral, FL) is a flatness and leveling measuring system with an automatic rotating laser. The LEVALIGN EXPERT provides an accurate and easy to use method for the measurement of flatness and straightness of machine bases and foundations, split machine casings, and flatness and parallelism of circular, rectangular, and odd-shaped flanges.
Gateway Safety (Cleveland, OH) introduces Swap, a new eyewear solution that can easily switch spectacles to goggles with a snap. Each pair includes both temples to wear it as safety glasses and a head strap to switch to goggles. The Swap frame is fully lined with soft, smooth foam that blocks dust and debris.
Formulated for electrical potting and encapsulation applications, Master Bond EP36AO from Master Bond (Hackensack, NJ) combines high thermal conductivity with thermal stability. It is serviceable from -80°F to 500°F, has a tensile strength of over 2,000 psi, and can adhere to metallic and non-metallic substrates.
AutomationDirect (Cumming, GA) now offers Wera standard, insulated, and miniature screwdrivers in six-piece sets. Screwdriver handles are marked with a screw symbol and the tip size for easy identification. A laser treatment provides a microrough surface on the tip of the blade for less slipping.
The new angle grinder from Metabo (West Chester, PA) is ideal for cutting, grinding, and deburring applications. The W680 4½ inch angle grinder features a 6.2 amp motor with 680 watts of power, 14 inch-pounds of torque, and a no-load speed of 11,000 rotations per minute. Weighing 4.
Swagelok (Solon, OH) has added five new tools to its orbital welding and tubing equipment lines. The new product selection includes four new tube facing tools and one cutting tool. The tools are intended for use with 316 stainless steel, carbon steel, and most nickel-based alloys. The new tube facing tools are available in four different sizes (TF16, TF24, TF40, and TF72) and feature coated tool bits with cutting edges and built-in electronic speed regulation.