The accredited 2-part Electrical Machinery Diagnostics Workshop (EMDW) focuses on the electrical machinery theory and operation, practical concepts and analysis skills needed to efficiently address the issues that plague electrical reliability programs. EMDW discusses electrical and operational theories and evaluates common electrical machinery diagnostic techniques, providing insight into the strengths, weaknesses and appropriate application of each technique.
A federal agency is proposing nearly $133,000 in fines for a Hastings cold storage plant, alleging more than a dozen safety violations. The U.S. Department of Labor's Occupational Safety and Health Administration says in a news release that workers were exposed to anhydrous ammonia at the Nebraska Cold Storage Inc. plant.
Lately, there has been a lot of buzz about the new and emerging technologies in manufacturing that are likely to produce major industry changes in the coming months and years. One such area of technology, as identified by the Advanced Manufacturing Partnership (AMP) group, is remanufacturing.
Police fired rubber bullets and tear gas Monday in the third day of clashes with thousands of garment workers demanding better minimum wages amid escalating tension over the country's main export business. Police said the violence mainly took place in the Gazipur and Savar Industrial zones, just outside the capital of Dhaka.
Secretary of Labor Thomas E. Perez announced $474.5 million in grants to community colleges and universities around the country for the development and expansion of innovative training programs in partnership with local employers. The grants are part of a multiyear, nearly $2 billion initiative to expand targeted training programs for unemployed workers, especially those impacted by foreign trade.
The risk of slips and falls is one every business must face, but industrial environments contend with the added challenge of preventing significantly more dangerous incidents. With heavy machinery, rotating equipment, sharp corners, and other various dangers around every corner, it’s critical manufacturers stress safety… and what better place to start than the floors.
When people look to chemical threadlockers, they are almost always looking to secure a troublesome fastener from vibrating loose. However, a key advantage of anaerobic threadlockers often overlooked is their ability to seal the threaded joint from leaks.
A typical manufacturing plant today will have thousands, or even many thousands, of electrical connections on both fixed equipment and moving machines. And it’s just a matter of time before some of those connections fail or wear out, bringing production machines to a dead stop.
Ford Motor Company is a global automotive industry leader, manufacturing or distributing vehicles across six continents. With 175,000 employees and 65 plants worldwide, the company has leveraged the dedication of its employees and UAW partnership to become more efficient, improve its product cadence, and be a more effective automotive industry competitor than ever before.
U.S. health regulators have placed a ban on imported drugs from a factory operated by India's largest pharmaceutical company, Ranbaxy Laboratories, due to manufacturing and quality control problems. The import alert, issued Friday by the Food and Drug Administration, effectively stops imports of 11 drugs from Ranbaxy's Mohali factory in Punjab province.
In this issue, Ford readies its Kansas City location for 2,000 new jobs, a connector expert explains how to prevent downtime, experts discuss proper product selection for threadlocking and gasketing, and more.
Drilling and fracking for natural gas do not seem to spew immense amounts of the greenhouse gas methane into the air, as has been feared, a new study says. The findings bolster a big selling point for natural gas, that it's not as bad for global warming as coal. And they undercut a major environmental argument against fracking, a process that breaks apart deep rock to recover more gas.
The fouling of heat exchangers in processing industries is a chronic operating problem. Costs due to additional fuel consumption and maintenance, loss of production, etc. have been estimated as 0.25 percent of the GNP of industrialized countries. EWT offers companies an environmental, effective, and cost saving method of reducing fouling on heat exchangers which can only prove a win, win, win scenario for all.
The median age of the labor force is anticipated to increase rapidly, with one-third of the U.S. labor force turning 55 by 2015. This may have far-reaching implications on the number and type of work-related injuries experienced. Most companies are not prepared for these changing demographics.
Politicians love promoting "made in America" during an election season but tend to forget about it once the dust settles. And so, for all the praise of American manufacturing in the last campaign – by Democrats and Republicans alike – very little has actually been done. So what happened to a real competitiveness – and – jobs agenda?
Crimp quality detection is similar to baking a cake. There are a lot of ingredients and if one ingredient is missing or of bad quality, you likely are not going to achieve your desired result. This article will go back through the basics of a crimp quality detection system and discuss what ingredients or variables you need to consider before switching off that CFM.
The electronic devices used to test and analyze electric motors and other equipment have become much more powerful than in the past. Yet, in many instances these sophisticated devices have also introduced a high degree of complexity for users, requiring that highly trained and experienced personnel perform the testing.
Nobody has been hurt in a fiery drilling rig accident in rural South Texas and efforts continue to put out the blaze. The Lavaca County Sheriff's Office says the accident happened Wednesday night between Shiner and Yoakum. The area is about 80 miles east of San Antonio.
State environmental officials on Wednesday were investigating an oil spill at a refinery that left a sheen floating on the Delaware River. The refinery in Delaware City, operated by PBF Energy, reported the release about 1:30 a.m. Wednesday.
One of southern Illinois' biggest employers now has a new railroad spur as it presses ahead with a $129-million expansion it says will add 100 jobs by mid-2015. The $1.1 million spur paid for by Illinois taxpayers was unveiled Tuesday at the 3,000-worker Continental Tire the Americas site that produces more than 14 million tires a year in Mount Vernon.
Programmable drives are becoming more sophisticated and capable, enabling controls engineers to drastically reduce project costs. On a new design, some integrators and OEMs reach for an elaborate multi-axis PLC system to solve a relatively simple application. This happens as designers work under compressed schedules, and choosing a familiar solution seems like the right thing to do.
Federal regulators announced plans to dramatically limit workplace exposure to silica dust, an agent known to cause crippling lung disease and cancer in thousands of workers each year. The proposal from OSHA would cut in half the amount of silica exposure allowed for general industry and maritime workers.
Ford Automotive has unveiled what it says is an industry-first detection technology that uses high-resolution cameras to detect and eliminate dirt particles on a freshly-laid coat of paint. The company’s F-Series trucks are the latest vehicles to benefit from the technology, which Ford claims can detect particles smaller than a grain of salt.
Seals for processing equipment play vital roles in protecting bearings and lubricants. From the perspective of managing lubrication, a seal’s primary purpose will be to retain lubricant and keep contaminants from degrading or harming the grease.
Few industrial environments can match the diverse and difficult operating conditions encountered in the food and beverage processing industries. Equipment often will be exposed to contaminants, frequent washdowns can degrade machinery and may cause lubricant leakage, and other adverse influences can combine to impact an operation’s lines and productivity.