Not too long ago, Monster.com, the well-known online job marketplace, conducted a comprehensive survey on the state of U.S. manufacturing jobs, and came to some compelling, if not worrying, results. In general, workers in U.S. manufacturing are largely unhappy with their current positions, for a variety of reasons, and are more likely to be actively searching for different work, be it at another plant, or another industry.
We’re still in a slow recovery period and there are things to be concerned about if they materialize, such as issues in the Middle East and Federal government spending. So manufacturing is not out of the woods yet, but nevertheless, two solid months to start the second half is a good sign.
Explosion proof fixtures provide protection by preventing any ignitions within the fixture housing from igniting the atmosphere outside of the fixture. Intrinsically safe fixtures are more specialized and provide their protection by being low powered and incapable of producing enough heat or spark to produce ignition.
Industrial lighting systems although performing the same basic role as lighting in any other setting by providing illumination in areas where available light is inadequate, must also address a host of factors that never come into play in common non commercial/industrial settings.
Crimp quality detection is similar to baking a cake. There are a lot of ingredients and if one ingredient is missing or of bad quality, you likely are not going to achieve your desired result. This article will go back through the basics of a crimp quality detection system and discuss what ingredients or variables you need to consider before switching off that CFM.
The electronic devices used to test and analyze electric motors and other equipment have become much more powerful than in the past. Yet, in many instances these sophisticated devices have also introduced a high degree of complexity for users, requiring that highly trained and experienced personnel perform the testing.
The iconic Rosie the Riveter may seem to be simply a fiction from the past but she has a name – and an important history. She was part of that migration, part of the 40,000 employees at the Ford-run Willow Run B-24 bomber plant and part of the great Arsenal of Democracy that Detroit and the Southeastern Michigan region became, cranking out airplanes, tanks, trucks, and weapons.
Last week, Walmart Stores announced that they would be holding a summit on U.S. manufacturing, and there’s a fair amount of skepticism over the company’s motives, particularly considering its long history of sourcing a vast majority of products from overseas.
Programmable drives are becoming more sophisticated and capable, enabling controls engineers to drastically reduce project costs. On a new design, some integrators and OEMs reach for an elaborate multi-axis PLC system to solve a relatively simple application. This happens as designers work under compressed schedules, and choosing a familiar solution seems like the right thing to do.
With the emergence of 3D printers into mainstream markets, what the devices actually do seems to matter less than what they will do, or could be made to do, in the future. Will they create a crisis of unregistered, undetectable firearms? Or will 3D printers become such a life-saving medical necessity that future consumers will regard the technology as unremarkable as the current practice of casting broken bones?
It’s no secret that one of the most pressing issues facing U.S. manufacturing is a lack of qualified workers. In looking to fill this skills gap, Brian Binke, the President & CEO of The Birmingham Group, an affiliate of MRINetwork and one of the world’s largest recruitment organizations, feels that organizations need to focus on several internal facets in attracting the best and most qualified people.
On the evening of April 20, 2010, Deepwater Horizon suffered a blowout while drilling in the Macondo Prospect, an area in the Gulf of Mexico 40 miles off the southeast coast of Louisiana. The platform caught fire; two days later, it sank.
Seals for processing equipment play vital roles in protecting bearings and lubricants. From the perspective of managing lubrication, a seal’s primary purpose will be to retain lubricant and keep contaminants from degrading or harming the grease.
In the last twelve months, the compressor industry has seen the release of several innovative, patented air compressor technologies that significantly reduce energy consumption. These recent advancements derive from improvements throughout the compressor design and contribute to dramatic increases in energy efficiency.
Few industrial environments can match the diverse and difficult operating conditions encountered in the food and beverage processing industries. Equipment often will be exposed to contaminants, frequent washdowns can degrade machinery and may cause lubricant leakage, and other adverse influences can combine to impact an operation’s lines and productivity.
Manufacturers are eager to streamline complex processes in an effort to produce significant cost and time savings while increasing overall productivity and profitability. However, streamlining long-established processes can be a daunting, time-consuming endeavor.
Maker’s Row, a free service that facilitates connections between designers and the small-batch American manufacturers that can help them turn a sketch into a real product, is on a roll. The startup has recently secured $1M in funding. The users are happy too — Tanya Menendez, COO and co-founder, was pleased to hear that an American manufacturer posted their company’s profile and had a meeting in just two days.
From the corner offices across America to the halls of Capitol Hill, leaders in the public and private sectors are sounding the call for economic reform and job creation. As the U.S. looks to forge a path for sustainable economic growth for the nation, there is a powerful business tool that can help U.S. industry to fuel business performance and drive growth.
Over the past two months, Software Advice has surveyed maintenance professionals to identify how the industry uses software to get organized, improve efficiencies and tackle other industry challenges. 84 percent of those surveyed use some kind of software to manage maintenance. Commercial software products (i.e. CMMS, EAM/ERP or other business software tools) were used by 77 percent of those surveyed.
According to recent figures from the South Carolina Department of Commerce, the state’s GDP growth rate of 2.7 percent puts it just above the 2.5 percent national average, and is significantly out-pacing the 2.1 percent average of the southeastern region of the country. Much of this growth is attributed to manufacturing.